Garage Door Opener Remote Control TecKey TK1010 How To Coding Instructions
MODEL TK-1010 TRANSMITTER
************* WARNING *************
Moving Door can cause serious injury or death.
DO NOT install transmitter unless the door operator’s safety reverse works as required by the door operator’s manual.
During programming the garage door may operate. Keep people and objects clear of the moving door to prevent door damage or possible personal injury.
NEVER let children operate or play with door controls. Keep remote controls away from children. Fatal injury could result should a child become trapped between the door and the floor.
ALWAYS keep moving door in sight and away from people and objects until it is completely closed. To prevent serious injury or death, avoid standing in the open doorway or walking through while door is moving.
Wall control must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts.
Keep people clear of opening while door is moving.
DO NOT allow children to play with the transmitter or door operator.
If safety reverse does not work properly:
Close door then disconnect operator using the manual release handle.
DO NOT use transmitter or door operator.
Refer to Door and Door Operators Owner’s Manuals before attempting any repairs
Electrical Shock can cause serious injury or death.
Power cord must be unplugged before attaching any wires,
Be sure wire ends do not touch each other or other terminals.
If you have questions or if you need a manual, contact the distributor or manufacturer of the operator
Setting Your Personal Code
Remove the rectangular covers from the transmitter and receiver. Locate the code switches on the receiver and the transmitter. The coding switches are located in the bottom half of the transmitter. Use a pen or paper clip to change the switches to any other code you desire by moving each of the ten switches to either the “ON” or “OFF” position. Any combination of switches can be selected. Make sure that the transmitter and receiver have the same switch settings. DO NOT have the switches either all to the “ON position or all to the “OFF” position.
The transmitter is supplied with a metal clip to attach the unit to a sun visor. If you wish to use the clip, slide it into the recess provided on the back of the case until the dimples on the case fit into the small holes in the clip
The transmitter is supplied with a standard 9-volt battery which is installed at the factory. After approximately one year the battery may need to be replaced. Replacement is indicated by less brightness in the indicator light or reduced range of operation. The battery is located under the transmitter cover. To replace the battery, remove the cover and carefully unsnap the battery clip. Snap the new fresh battery in place and replace the cover.
If additional transmitters are desired, you need only to match the code switches on the new unit to the existing code. The unit is then ready to operate.
The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such they have limited transmitter power and therefore limited range.
A receiver cannot respond to more than one transmitter signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.
Changes or modifications in the device may void FCC compliance.
garage-door-openers.us - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981. Providing excellent customer service and assistance for over 25 years. We are a discount reseller of garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community. We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. All mentioned brand names of Garage Door openers, Garage Door opener receivers and Gate operator devices are registered trade names and trademarks of the respective entities and are only used for reference.
Copyright © 2018 garage-door-openers.us No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.