Garage Door Openers, Garage Door Opener Parts, Access Controls, Garage Door Opener Remote Control and Garage Door Keypad

garage-door-openers.us your garage door opener specialists <td width="100%" height="1
 

 

 Home

Contact Us 1-480-247-2094

About Us

Shipping

Follow us on Facebook

1st Garage Door Openers, Inc.
 BBB Business Review

Stanley

Remotes

Receivers

Keyless Entry and Wall Controls

Repair Parts

Telectron

Allister,Allstar

Remotes

Keypads and Wall Controls

Receivers

Repair Parts

Challenger Repair Parts

Tec Key TK1010 Remote

Marantec

Remotes

Repair Parts

LiftMaster

Remotes

Keyless Entry

Repair Parts

Receivers

Logic Boards

Surge Protection

Safety Sensors

Wall Controls

Motor Heads

Garage Door Opener Systems

Battery Backup

Accessories

Multi-Code

Remotes

Keypads

Receivers

Universal

Linear Delta3

Remotes

Keypads

Receivers

Repair Parts

Moore O Matic Parts

Heddolf, ESP Micom

Wayne Dalton

Remote Controls and KeyPads

Wall Controls

Repair Parts

Lubricants

Driveway Alert by Optex

Garage Accessories
Customer Assistance
Shipping and Returns
Warranty Information
Cancellation Policy
About Us
Fax or check Order form
Site Index

All orders are shipped same or next day!!!

VISA, Mastercard, American Express and Discover

Review www.garage-door-openers.us on alexa.com

Genie Garage Door Opener Wireless Garage Door Keypad Old Style Black Programming Instructions

GWKIC and ACSDG

INSTALLATION AND PROGRAMMING INSTRUCTIONS

  1. INSTALLATION INSTRUCTIONS         
  2. BASIC PROGRAMMING         
  3. PROGRAMMING MULTIPLE DOOR OPERATORS
  4. ENHANCED PROGRAMMING

Features

  • Controls up to three doors.

  • Panic control – Once control is established and for 30 seconds thereafter, any button will control door.

  • Two Permanent Personal Identification Numbers (PIN).

  • Temporary PIN for special purpose access.

  • Any PIN can be up to 8 digits long.

  • Lighted Keypad for ease of use at night.

  • Indicator Light gives visual confirmation of key presses.

*************   WARNING   *************

            Moving Door can cause serious injury or death.

·         DO NOT install transmitter unless the door operator’s safety reverse works as required by the door operator’s manual.

·         Wall control must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts.

·         Keep people clear of opening while door is moving.

·         DO NOT allow children to play with the transmitter or door operator.

If safety reverse does not work properly:

·         Close door then disconnect operator using the manual release handle.

·         DO NOT use transmitter or door operator.

·         Refer to Door and Door Operators Owner’s Manuals before attempting any repairs.

 

            Electrical Shock can cause serious injury or death.

·         Power cord must be unplugged before attaching any wires,

·         Be sure wire ends do not touch each other or other terminals.

If you have questions or if you need a manual, contact the distributor or manufacturer of the operator.

 

1. INSTALLATION INSTRUCTIONS

    NOTE: For convenience in programming you may wish to install Wireless Keypad after Basic Programming of Wireless Keypad and Garage Door Operator(s) is completed.

·     Mount wireless keypad on a flat vertical surface with enough room above to slide cover up. pick location out of path of moving garage door and supporting hardware.

·      Slide Keypad Cover up and pull off wireless keypad. Slide off battery cover and remove battery.

·      Mark two holes by tapping a small nail through screw holes on keypad. Drill 1/16’ pilot holes then fasten with #6 screws enclosed. Replace Keypad cover.

·      Replace battery and slide battery cover back into place.

2.  BASIC PROGRAMMING

                                   How to enter Personal Identification Number (PIN 1).

                                   How to reset the Wireless Keypad memory.

           A. PROGRAMMING THE WIRELESS KEYPAD

 

Entering PIN 1        ACTION                                         KEYPAD INDICATOR

                              Open cover fully                               Blinks once and goes out

                              Press 3-5-7          

                              Press “PROG”                                 Blinks once each second

                              Enter PIN 1 (up to 8 digits)            

                              Press “PROG”                                 Double blinks each second

                              Close cover fully

       NOTE: Your wireless Keypad is now ready to signal your Door Operator. Your Door Operator must be programmed to accept the signal from your Wireless Keypad.

       Resetting the Wireless Keypad---------------------------------

·         Open cover half way.

·         Press and hold “PROG” and “8” while fully opening cover

·         INDICATOR will blink once and go out.

·         Close cover fully.

       NOTE: Wireless Keypad memory is now set the same as when it left the factory.

                  Return to Entering PIN 1.

 

            B. PROGRAMMING 1 DOOR OPERATOR

 

                 How to program your Door Operator to receive the signal from your Wireless Keypad.

 

*************   WARNING   *************

During this programming the Door Operator could begin to run. Be sure to stay away from the moving door and it’s parts. To prevent the door from moving, close door then disconnect it from the Door Operator by pulling the Red Emergency Release Handle.                               

 

Find the Learn Code Button and Radio Signal Indicator located on the Door Operator power head. Open Wireless Keypad Cover fully.  This can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find Learn Code Button).

                              ACTION                                                           KEYPAD INDICATOR

                              Press Operator Learn Code Button                     Blinks

                              Enter PIN 1

                              Press “SEND”                                                   Stays on

                              Press “SEND”                                                   Goes out

                              Press “SEND” to Test System                            Motor Runs.

                              Press “SEND” to Test System                            Motor Stops.

Use the Emergency Release to reconnect the Door to the Door Operator. Your system is now ready to use.

        C.  CONTROLLING 1 DOOR OPERATOR

 

                              ACTION                                                           KEYPAD INDICATOR

                              Open Cover                                                       Wait for Keypad indicator to go out before

                                                                                                      Pressing any buttons.

                              Enter PIN1                                                        Indicator blinks with each key press.

      Press and hold "SEND"                                      Door moves if only 1 door.

      Close cover fully

           NOTE:     - if indicator is solid, PIN 1 was entered correctly.

                          - if indicator blinks, PIN1 was entered incorrectly. Close cover and start

                            C. CONTROLLING 1 DOOR OPERATOR over.

           NOTE:  Any Keypad button will control the door within 30 second after door begins to move or until cover is closed.

       

        3.  PROGRAMMING MULTIPLE DOOR OPERATORS

 

             How to add Door Operators 2 and 3 to Wireless Keypad.

             How to program your door Operator to receive the signal from your Wireless Keypad.

 

*************   WARNING   *************

During this programming the Door Operator could begin to run. Be sure to stay away from the moving door and it’s parts. To prevent the door from moving, close door then disconnect it from the Door Operator by pulling the Red Emergency Release Handle.                               

 

               A.  ADDING MORE DOORS TO THE WIRELESS KEYPAD

 

                             ACTION                                                         KEYPAD INDICATOR

                             Open cover fully                                                  Blinks once and goes out

                             Enter PIN 1

                             Press “PROG”                                                    Blinks once each second

                             Press “PROG”                                                    Double blinks each second

                             Press “PROG”                                                    Triple blinks each second

                             Enter total number of doors (2or3)           

                             Press “PROG”                                                    Goes out

                             Close cover fully.

 

       NOTE: Your Wireless Keypad is now ready to signal your door operators. Each Door Operator must be programmed to accept the signal from your Wireless Keypad. Decide which Door Operator will be Door 1, Door 2 and Door 3.

 

               B.  PROGRAMMING MULTIPLE DOOR OPERATORS

 

Find the Learn Code Button and Radio Signal Indicator located on the Door Operator power

Head Open Wireless Keypad cover fully.

                            ACTION                                                  RADIO SIGNAL INDICATOR

                            Press Operator Learn Code Button                       Blinks

                            Enter PIN 1

                            Press “SEND”

                            Enter Door Number (1,2or 3)                                Stays on

                            Press “SEND”                                                    Goes out

                            Press “SEND” to Test System                             Motor Runs

                            Press “SEND” to Test System                             Motor Stops

                            Close Wireless Keypad cover fully

Use the Emergency Release to reconnect the Door to the Door Operator. Your system is now ready to use. If you are programming another Door Operator go to that machine and repeat the above steps.

 

               C.  CONTROLLING MULTIPLE DOOR OPERATORS

 

                            ACTION                                                             KEYPAD INDICATOR

                            Open cover                                                   Wait for keypad indicator to go out

                                                                                                before pressing any buttons.

                            Enter PIN 1                                                   Indicator blinks with each key press.

                           *Press “SEND”                                             

                           *Enter Door Number (1,2 or 3)                          Door moves.

                            Close cover fully

       NOTE:  - if indicator is solid, PIN was entered correctly.

                   - if indicator blinks, PIN was entered incorrectly. Close cover and start

                     C. CONTROLLING MULTIPLE DOOR OPERATORS over.

       NOTE:  Any Keypad Button will control the door within 30 seconds after door begins to move or until cover is closed.

 

        4.  ENHANCED PROGRAMMING

 

             How to add a Second Personal Identification Number (PIN2).

             How to change Personal Identification Number (PIN 1 or PIN 2).

             How to add and cancel a Temporary Personal Identification Number (PIN).

 

Changing a PIN   ACTION                                                         KEYPAD INDICATOR

                           Open cover fully                                               Blinks once and goes out.

                           Enter PIN to be changed

                           Press “PROG”                                                 Blinks once each second

                           Enter New PIN                                  

                           Press “PROG”                                                 Double blinks if PIN 1 changed

                                                                                                 Goes out if PIN 2 changed

                           Close cover fully

        NOTE: Your Wireless Keypad is now ready to signal your Door Operator(s). Your Door operator(s) must be programmed to accept the signal from your Wireless Keypad.

 

                     SEE 2B PROGRAMMING 1 DOOR OPERATOR OR 3B PROGRAMMING MULTIPLE

                     DOOR OPERATORS.

 

Adding PIN 2      ACTION                                                         KEYPAD INDICATOR

                                   Open cover fully                                              Blinks once and goes out

                          Enter 1-5-9

                          Press “PROG”                                                              Blinks once each second

                          Enter PIN 2 (up to 8 digits)                            

                          Press “PROG”                                                Goes out

                          Close cover fully

                                           

          NOTE:  Your Wireless Keypad is now ready to signal your Door Operator(s). Your Door Operator(s) must be programmed to accept the signal from your Wireless Keypad.

 

                    SEE 2B PROGRAMMING 1 DOOR OPERATOR or 3B PROGRAMMING MULTIPLE

                    DOOR OPERATORS.

 

Adding Temporary PIN

                         ACTION                                                          KEYPAD INDICATOR

                         Open cover fully                                               Blinks once and goes out

                         Enter PIN 1

                         Press “PROG”                                                 Blinks once each second

                         Press “PROG”                                                 Double Blinks each second

                         Enter Temporary PIN

                         Press “PROG”                                                 Triple blinks each second

                         Close cover fully

            NOTE:  Your Wireless Keypad is now ready to signal your Door Operator(s). You do not need to reprogram your Door Operator(s).

 

Cancelling the Temporary PIN___

                                The Temporary PIN will remain active until the next time PIN 1 is entered. Entering PIN 1 cancels the Temporary PIN.

garage-door-openers.us - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981.  Providing excellent customer service and assistance for over 25 years. We are a discount reseller of  garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community.   We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. All mentioned brand names of Garage Door openers, Garage Door opener receivers and Gate operator devices are registered trade names and trademarks of the respective entities and are only used for reference.

1st Garage Door Openers Inc.

Mesa, AZ  85203

1-480-247-2094

1-480-247-3498   Fax

Garage Door and Garage Door Openers

Copyright © 2018 garage-door-openers.us  No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.