Wayne Dalton Garage Door Opener Keyless Entry System Coding Instructions Model 327308
The following explains how your keyless entry can be used to OPEN, CLOSE, START, and STOP your door.
1. Enter your 5-digit PIN (personal identification number): door will begin to move.
NOTE: If you inadvertently enter an incorrect code, the door will not move. To reset, Simultaneously press and release the "7/8" and "9/0" buttons and reenter your PIN number.
2. Unit remains active for next 25 sec. Pressing any key will stop the door if opening, and stop or reverse the door if closing during the 25 sec. active period.
Under normal operating conditions, the battery should be changed every 12 months. To replace battery perform the following steps:
A. Snap open case with a coin and remove old battery.
B. Replace battery (one CR2032 ) and snap case together.
Dispose of used battery properly.
Programming or Changing Personal Identification Number
A. With new installations, we recommend the keyless entry be programmed before mounting to wall.
B. Unit should be programmed with garage door in the down position. For the iDrive® openers pull the emergency disconnect handle to the manual position (lower position).
C. Press the program button on the garage door opener to switch the opener to the learn mode. Opener will remain in the learn mode for at least 30 seconds.
D. Press the desired five digit PIN. Garage door opener should beep or lamp should blink. For the iDrive® openers, return the emergency disconnect handle to the motor operated position (upper position).
NOTE #1: Do not set a code that presents the numbers in sequential order. Also do not select a code that uses the same button five times consecutively.
NOTE #2: If any any time an error was made in entering the codes, simply simultaneously press and release the "7/8" and "9/0" buttons to reset the keyless entry, then repeat the above procedures.
NOTE #3: One 3966 Keyless entry can be programmed to open multiple garage door openers. To program fro additional openers, repeat steps A thru D above except input a different five digit PIN number for each additional opener.
garage-door-openers.us - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981. Providing excellent customer service and assistance for over 25 years. We are a discount reseller of garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community. We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. All mentioned brand names of Garage Door openers, Garage Door opener receivers and Gate operator devices are registered trade names and trademarks of the respective entities and are only used for reference.
Copyright © 2018 garage-door-openers.us No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.