Garage Door Openers, Garage Door Opener Parts, Access Controls, Garage Door Opener Remote Control and Garage Door Keypad your garage door opener specialists <td width="100%" height="1



Contact Us 1-480-247-2094

About Us


Follow us on Facebook

1st Garage Door Openers, Inc.
 BBB Business Review




Keyless Entry and Wall Controls

Repair Parts




Keypads and Wall Controls


Repair Parts

Challenger Repair Parts

Tec Key TK1010 Remote



Repair Parts



Keyless Entry

Repair Parts


Logic Boards

Surge Protection

Safety Sensors

Wall Controls

Motor Heads

Garage Door Opener Systems

Battery Backup







Linear Delta3




Repair Parts

Moore O Matic Parts

Heddolf, ESP Micom

Wayne Dalton

Remote Controls and KeyPads

Wall Controls

Repair Parts


Driveway Alert by Optex

Garage Accessories
Customer Assistance
Shipping and Returns
Warranty Information
Cancellation Policy
About Us
Fax or check Order form
Site Index

All orders are shipped same or next day!!!

VISA, Mastercard, American Express and Discover

Review on

Multi Code Garage Door Opener and Gate Operator Remote Control Transmitter 3089 Programming Instructions




·        Disconnect power before any installation or repair.

·        Wear safety glasses.

Congratulations! You have just purchased a MULTI-CODE Digital Transmitter, which we believe to be the finest product of it’s kind on the market.  With a little care this transmitter should provide you with many years of excellent service. Please take a moment to read the following instructions and you will find that setting your new transmitter will be quite an easy matter.


On the model 3098 the entire front lower half of the transmitter is removable.  Grasp the front lower half of the case near the bottom on both sides and pull upward away from the transmitter, this will disengage the lower end. Then pull downward to remove the lower cover, this will expose both the code switch and the battery compartment.


 You may set your transmitter to any code you desire but be sure that the code you set matches the code has been set on your radio receiver. The digital code is determined by the positions of the 10 small switches numbered 1 through 10 located in the receiver and transmitter. Any combination of ON (CLOSED) or OFF (OPEN) positions can be selected by using a small screwdriver or ball point pen. (NOTE: The switches are in the “On” position when the side next to the number is pressed in.) In setting your personal code we strongly urge that several coding schemes be avoided: ALL ON; ALL OFF; 2,4,6,8,10 ON; 1,3,5,7,9, ON. These positions are similar to our or other manufacturer’s test positions, or are frequently used. Once the code has been set, check the operation and replace the hatches.


 The transmitter is completely self  contained, including battery, and can be operated while mounted in the car. It is supplied with a clip for attaching to the sun visor, if desired. If the clip is used attach to the case by sliding it into the recess provided on the back of the transmitter until the small dimples fit into the holes in the clip.


 Replacement battery 9 volt NEDA1604 (Eveready 216 or equivalent).

 The battery in the transmitter can be checked or changed by removing the front lower half of the transmitter. Refer to the directions under “accessing the code switch” for battery replacement.


 A replacement or new transmitter or receiver may be purchased by specifying the model number and the RF frequency designated on the identification label. The RF frequency is set at the factory and must not be adjusted in the field. The digital code can be matched to the companion receiver or transmitter by following the above procedure. - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981.  Providing excellent customer service and assistance for over 25 years. We are a discount reseller of  garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community.   We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. All mentioned brand names of Garage Door openers, Garage Door opener receivers and Gate operator devices are registered trade names and trademarks of the respective entities and are only used for reference.

1st Garage Door Openers Inc.

Mesa, AZ  85203


1-480-247-3498   Fax

Garage Door and Garage Door Openers

Copyright © 2018  No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.