Garage Door Openers, Garage Door Opener Parts, Access Controls, Garage Door Opener Remote Control and Garage Door Keypad

garage-door-openers.us your garage door opener specialists Sales 1-480-247-2094

 

 Home

Contact Us

About Us

Shipping

Follow us on Facebook

1st Garage Door Openers, Inc.
 BBB Business Review

Stanley

Remotes

Receivers

Keyless Entry and Wall Controls

Repair Parts

Telectron

Allister,Allstar

Remotes

Keypads and Wall Controls

Receivers

Repair Parts

Challenger Repair Parts

Tec Key TK1010 Remote

Marantec

Remotes

Repair Parts

LiftMaster

Remotes

Keyless Entry

Repair Parts

Receivers

Logic Boards

Surge Protection

Safety Sensors

Wall Controls

Motor Heads

Garage Door Opener Systems

Battery Backup

Accessories

Multi-Code

Remotes

Keypads

Receivers

Universal

Linear Delta3

Remotes

Keypads

Receivers

Repair Parts

Moore O Matic Parts

Heddolf, ESP Micom

Wayne Dalton

Remote Controls and KeyPads

Wall Controls

Repair Parts

Lubricants

Driveway Alert by Optex

Garage Accessories
Customer Assistance
Shipping and Returns
Warranty Information
Cancellation Policy
About Us
Fax or check Order form
Site Index

All orders are shipped same or next day!!!

VISA, Mastercard, American Express and Discover

Review www.garage-door-openers.us on alexa.com

Garage Door Remote Control Transmitter Delta 3 DT4B Programming Instructions

DESCRIPTION:The Delta-3 DT-4B digital transmitter is a four-channel wireless radio control designed for use with automatic garage/gate operators and access control systems. The transmitter can be used with one four-channel receiver (DR4), two two-channel receivers (DR2) or four single-channel receivers (DR ,DRQ or DRM). Receivers should be mounted at least 8 feet apart.The Delta-3 radio format provides 256 different digital codes. The codes are set using the 8-position coding switches in the units.

Caution: All transmitters and receivers should be recoded by the installer prior to operation.

In order to avoid the possibility of duplicating codes in adjacent systems, factory set codes should not be used. In addition, among the valid codes available, four others should not be used. These include: all keys set ON or OFF and keys set alternating ON/OFF.

The transmitter is powered by a 9-volt battery. It should last 12 to 18 months with normal use. The red LED on the face of the transmitter will glow when the unit is activated. When it lights dimly, or not at all when transmitting, the battery needs to replaced.

Step 1: Locate Coding Switches. Locate coding switch. Remove the battery access door located on the back of the transmitter case. Identify the coding switch and note that it has eight positions, with ON and OFF clearly labeled.

Step 2A: Coding for single-channel receivers.  Pick any combination of OFF/ON codes and set them on the switch keys 3-8 in the transmitter. Match the same code on switch keys 3-8 in each receiver. Set each receiverís switch keys 1 and 2 to select which transmitter button will activate it. Use a paper clip or other pointed object (except a pencil or pen).

Step 2B: Coding for two-channel receivers. Pick any combination of OFF/ON codes and set them on switch keys 3-8 in the transmitter. Match the same code on switch keys 3-8 in each receiver. Set each receiverís switch key 2 to select which transmitter buttons (1 & 2, or 3 & 4) will activate it. Transmitter switch keys 1 & 2 and receiver switch key 1 are unused and can be in any position.

Step 2C: Coding for a four-channel receiver. Pick any combination of OFF/ON codes and set them on switch keys 3-8 in the transmitter. Match the same code on switch keys 3-8 in each receiver. Transmitter and receiver switch keys 1 & 2 are unused and can be in any position.

 Step 3: Test the equipment. Connect the receiver(s) to the operators as described in the receiverís installation instructions. Be sure the door/gate area is clear. Activate the transmitter and verify that the receiver triggers the operator. Check that the correct button on the DT-4B activates the desired operator.

 Battery Replacement: The battery should last 12 to 18 months with normal use. The red LED on the face of the transmitter will glow when the unit is activated. When the red LED lights dimly, or not all when transmitting, the battery needs to be replaced. Remove the battery access door to change the battery. Any type of 9-volt battery can be used.

IMPORTANT!!!!

Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there are some limitations, which must be observed.

∑        For U.S. installations only: The radios are required to comply with FCC rules and regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range.

∑        A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.

∑        Changes or modifications to the device may void FCC compliance.

∑        Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

∑        A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.

 

This device complies with FCC Rules Part 15 and 1C Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

 

   



garage-door-openers.us - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981.  Providing excellent customer service and assistance for over 25 years. We are a discount reseller of  garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community.   We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. All mentioned brand names of Garage Door openers, Garage Door opener receivers and Gate operator devices are registered trade names and trademarks of the respective entities and are only used for reference.

1st Garage Door Openers Inc.

Mesa, AZ  85203

1-480-247-2094

1-480-247-3498   Fax

Garage Door and Garage Door Openers

Copyright © 2017 garage-door-openers.us  No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.