Garage Door Openers, Garage Door Opener Parts, Access Controls, Garage Door Opener Remote Control and Garage Door Keypad

garage-door-openers.us your garage door opener specialists Sales 1-480-247-2094

 

 Home

Contact Us

About Us

Shipping

Follow us on Facebook

1st Garage Door Openers, Inc.
 BBB Business Review

Stanley

Remotes

Receivers

Keyless Entry and Wall Controls

Repair Parts

Telectron

Allister,Allstar

Remotes

Keypads and Wall Controls

Receivers

Repair Parts

Challenger Repair Parts

Tec Key TK1010 Remote

Marantec

Remotes

Repair Parts

LiftMaster

Remotes

Keyless Entry

Repair Parts

Receivers

Logic Boards

Surge Protection

Safety Sensors

Wall Controls

Motor Heads

Garage Door Opener Systems

Battery Backup

Accessories

Multi-Code

Remotes

Keypads

Receivers

Universal

Linear Delta3

Remotes

Keypads

Receivers

Repair Parts

Moore O Matic Parts

Heddolf, ESP Micom

Wayne Dalton

Remote Controls and KeyPads

Wall Controls

Repair Parts

Lubricants

Driveway Alert by Optex

Garage Accessories
Customer Assistance
Shipping and Returns
Warranty Information
Cancellation Policy
About Us
Fax or check Order form
Site Index

All orders are shipped same or next day!!!

VISA, Mastercard, American Express and Discover

Review www.garage-door-openers.us on alexa.com

Digi Code Garage Door Opener and Gate Operator Remote Control Transmitter 5062 Programming Instructions

 

Garage Door Opener Radio Controls

Model 5060/5061  (300 MHz) – 5062/5063 (310 MHz)

Two Button Transmitters

 

WARNING:

·        Disconnect operator power before any installation or repair

·        Always wear safety glasses

 

Your Digi-Code controls are designed specifically to remotely control a garage door opener from within an automobile and to give years of trouble free service without adjustment. Because all radio controls are set with the even numbered switches in the “ON’ position when they leave the factory, it is recommended that a different code be selected and set at the time of installation. Please refer to the “Setting the Code Switches” section for instructions. The radio frequency (RF) portion of the controls, however, are tuned to standard frequencies and are thoroughly tested at the factory. This permits the addition or replacement of either the transmitter or the receiver by specifying the Model number and the RF frequency designated on the identification label. RF adjustments are not needed nor should any be attempted.

 

SECTION #1

SETTING THE CODE SWITCHES

On the transmitter the entire front lower half of the case (“the battery hatch”) is removable. Use a coin or the curved end of the visor clip to disengage the lower half of the transmitter front. This will expose both the code switch and the battery compartment.

 

Once you have removed the battery hatch, locate the “CODE SWITCHES” above the battery. As shown above, the left button is controlled by the left hand switch and the right button is controlled by the right hand switch.

 

Before setting the receiver code switches, you will need to set the transmitter code switches on your model 5060/5061 or 5062/5063. We strongly suggest that you change the code from the factory setting to provide security for your own system, and to eliminate interference with neighboring systems.

 

SETTING THE DUAL BUTTON SWITCHES

 

Set code switch positions 1 through 10 to your personal code scheme for the left button, any combination of “on” or “off” positions can be selected (NOTE: The switch is in the “on” position when it is depressed toward the number.) We strongly urge that several coding schemes be avoided: ALL ON; 2,4,6,8,10 ON. These positions are similar to our or other manufacturers test positions, or are frequently used. Repeat this step for the right button.

SETTING RECEIVER #1 (WORKS WITH LEFT BUTTON)

Set the receiver code switches to match the code settings you entered for the left button switch in the transmitter, being sure both are set the same since a different setting of just one switch will prevent operation.

 

SETTING RECEIVER #2 (WORKS WITH RIGHT BUTTON)

Set the receiver code switches to match the code settings you entered for the right button switch in the transmitter, being sure both are set the same since a different setting of just one switch will prevent operation.

 

Once the codes have been set, check operation.

 

SECTION #2

 

SETTING THE TRANSMITTER CODE SWITCHES-TO WORK WITH EXISTING STANLEY GARAGE DOOR OPENERS (Model 5062/5063 – ONLY).

 

Set the transmitter using “SETTING THE CODE SWITCHES” instructions from section #1 above.

 

Set the first garage door opener using “SETTING RECEIVER #1 (WORKS WITH LEFT BUTTON)” instructions from section #1 above.

 

Set the second garage door opener using “SETTING RECEIVER #2 (WORKS WITH RIGHT BUTTON)” instructions from section #1 above.

 

SECTION #3

TRANSMITTER BATTERY REPLACEMENT

 

The battery in the transmitter can be checked or changed by removing the front lower half of the transmitter. Use a coin or the curved end of the visor clip to disengage the lower half of the transmitter front. This will expose the battery compartment. Replacement battery must be a 9-volt.

 

TO REPLACE OR ADD A SET

A replacement or new transmitter or receiver may be purchased buy specifying the Model Number and the RF frequency designated on the serial tag label. The RF frequency is set at the factory and must not be adjusted in the field. The digital code can be matched to the companion receiver or transmitter by following the “setting” procedures above.

 

OPERATIONAL CHECK

To check operation, move back about 50 feet and press the transmitter button. Operation should be reliable at this distance but environment and location of both the transmitter and receiver will effect the range. Try different mounting locations and positions in the vehicle. If operation is still undesirable, the problem may be isolated by:

 

1.   Checking the door operator. If the door will not open when the wall button is pressed, the problem is likely to be the operator. If the door will open by pressing the wall button, but not when the radio control button is pressed, the problem is probably in the radios.

2.   Replacing the transmitter battery.

 

If, after performing the above operational checks, the controls still do not function, they should be returned to your dealer for repair or replacement.

garage-door-openers.us - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981.  Providing excellent customer service and assistance for over 25 years. We are a discount reseller of  garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community.   We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. All mentioned brand names of Garage Door openers, Garage Door opener receivers and Gate operator devices are registered trade names and trademarks of the respective entities and are only used for reference.

1st Garage Door Openers Inc.

Mesa, AZ  85203

1-480-247-2094

1-480-247-3498   Fax

Garage Door and Garage Door Openers

Copyright © 2017 garage-door-openers.us  No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.