Garage Door Openers, Garage Door Opener Parts, Access Controls, Garage Door Opener Remote Control and Garage Door Keypad

garage-door-openers.us your garage door opener specialists Sales 1-480-247-2094

 

 Home

Contact Us

About Us

Shipping

Follow us on Facebook

1st Garage Door Openers, Inc.
 BBB Business Review

Stanley

Remotes

Receivers

Keyless Entry and Wall Controls

Repair Parts

Telectron

Allister,Allstar

Remotes

Keypads and Wall Controls

Receivers

Repair Parts

Challenger Repair Parts

Tec Key TK1010 Remote

Marantec

Remotes

Repair Parts

LiftMaster

Remotes

Keyless Entry

Repair Parts

Receivers

Logic Boards

Surge Protection

Safety Sensors

Wall Controls

Motor Heads

Garage Door Opener Systems

Battery Backup

Accessories

Multi-Code

Remotes

Keypads

Receivers

Universal

Linear Delta3

Remotes

Keypads

Receivers

Repair Parts

Moore O Matic Parts

Heddolf, ESP Micom

Wayne Dalton

Remote Controls and KeyPads

Wall Controls

Repair Parts

Lubricants

Driveway Alert by Optex

Garage Accessories
Customer Assistance
Shipping and Returns
Warranty Information
Cancellation Policy
About Us
Fax or check Order form
Site Index

All orders are shipped same or next day!!!

VISA, Mastercard, American Express and Discover

Review www.garage-door-openers.us on alexa.com

Digi Code Garage Door Opener and Gate Operator Remote Control Transmitter 5012 Programming Instructions

 

Digi Code Garage Door Opener Radio Controls

Model 5010/5011 (300MHz)5012/5013 (310MHz) Single Button Mini Transmitters

Model 5100 (300 MHz) / 5102 (310 MHz) Receivers

 

WARNING:

·        Disconnect operator power before any installation or repair

·        Always wear safety glasses

 

Your Digi-Code radio controls are designed specifically to remotely control from within an automobile and to give years of trouble free service without adjustment. Because all radio controls are set with the even numbered switches in the “ON” position when they leave the factory, it is recommended that a different code be selected and set at the time of installation. Please refer to the “Setting the Code Switch” section for instructions. The radio frequency (RF) portion of the controls, however , are tuned to standard frequencies and are thoroughly tested at the factory. This permits the addition or replacement of either the transmitter or the receiver by specifying the Model number and the RF frequency designated on the identification label. RF adjustments are not needed nor should any be attempted.

 

SECTION #1

RECEIVER INSTALLATION

The receiver is designed to mount directly to the operator.  It can be remotely installed if the operator terminal strip is not assessable, or if the power for the receiver is not obtainable from the operator.  To direct mount the receiver, simply loosen the terminal screws on the operator and insert the two-way lugs from the receiver under the screws along the wall button wires, and tighten the screws.

 

Place the antenna (a10 in black wire) in a vertical position as far from any metal as possible.

Operator Terminal are as follows:

1 – Common   -  to wall button

2 – Relay         - to wall button

3 – 24 Radio Power

 

For remote installation the receiver may be mounted near the operator head on a joist or the ceiling by using the mounting tab.  Order Model 5192-06 Adapter, which permits connection between the operator terminal and the two-way lugs on the receiver.

 

Connect wires as follows:

1 -  White wire to terminal “1” or common

2 – Black wire to terminal “2” or Relay

3 – Red Wire to terminal “3” or 24V Radio

4 – Connect push button wires to terminal ‘1” and “2”

 

SECTION #2

SETTING THE (“RECEIVER”) CODE SWITCHES – TO WORK WITH MODEL 5010/5011 AND MODEL 5012/5013 SINGLE BUTTON MINI TRANSMITTERS

Use your finger to slide the “code switch hatch”  from the receiver for access to the code switch.  On the transmitter the entire front lower half of the case (“the battery hatch”) is removable.  Use a coin or the curved end of the visor clip to disengage the lower half of the transmitter front.  This will expose both the code switch and the battery compartment.

 

ACCESSING THE CODE SWITCH AND BATTERY COMPARTMENT

The models 5040, 5042, 5070 & 5072 mini transmitter cases are made up of two halves which are held together by a small Phillips head screw. Removing this screw will allow access to the code switches and the battery compartment.

 

 

Model 5010/5010 (300 MHz) or 5012/5013 (310 MHz)

Set both the code switches to the code of your choice, being sure both are set the same since a different setting of just one switch will prevent operation.  The digital code is determined by the position of the 10 small switches numbered 1 through 10 located in the receiver and the transmitter.  Any combination of “ON” or “OFF” positions can be selected by using a pencil or a pen.  (NOTE: the switches are in the “ON” position when the switch is depressed toward the number.)

 

Once the codes have been set, check operation and reinsert the hatches.

 

SECTION #3

SETTING THE CODE SWITCHES ON THE MODEL’S 5012/5013 TO WORK WITH EXISTING STANLEY GARAGE DOOR OPENERS.

Set the transmitter code switch to match the switches already set on the back of the garage door opener.

 

Once the codes have been set, check operation and reassemble products.

 

 

SECTION #4

 

TRANSMITTER BATTERY REPLACEMENT

Replacement of battery in the transmitter can be changed by removing the front half of the transmitter.  Use a coin or the curved end of the visor clip to disengage the lower half of the transmitter front.  This will expose the battery compartment.  Replacement battery must be a 9-volt.

 

TO REPLACE OR ADD A SET

A replacement or new transmitter or receiver may be purchased by specifying the Model Number and the RF frequency designated on the serial tag label. The RF frequency is set at the factory and must not be adjusted. The digital code can be matched to the companion receiver or transmitter by following the “set-“ procedures above.

 

OPERATIONAL CHECK

To check operation, move back about 50 feet and press the transmitter button. Operation should be reliable at a distance but environment and location or both the transmitter and receiver will effect the range. Try different mounting locations and positions in the vehicle. If operation is still undesirable, the problem may be tested by:

 

     Checking the door operator. If the door will not open when the wall button is pressed, the problem is likely to be the operator. If the door will open by pressing the wall button, but not when the remote control button is pressed, the problem is probably in the radios.

 

   Replacing the transmitter battery.

 

After performing the above operational checks, the controls still do not function, the should be returned to the dealer for repair or replacement.

garage-door-openers.us - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981.  Providing excellent customer service and assistance for over 25 years. We are a discount reseller of  garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community.   We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. All mentioned brand names of Garage Door openers, Garage Door opener receivers and Gate operator devices are registered trade names and trademarks of the respective entities and are only used for reference.

1st Garage Door Openers Inc.

Mesa, AZ  85203

1-480-247-2094

1-480-247-3498   Fax

Garage Door and Garage Door Openers

Copyright © 2017 garage-door-openers.us  No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.