Garage Door Openers, Garage Door Opener Parts, Access Controls, Garage Door Opener Remote Control and Garage Door Keypad

garage-door-openers.us your garage door opener specialists Sales 1-480-247-2094

 

 Home

Contact Us

About Us

Shipping

Follow us on Facebook

1st Garage Door Openers, Inc.
 BBB Business Review

Stanley

Remotes

Receivers

Keyless Entry and Wall Controls

Repair Parts

Telectron

Allister,Allstar

Remotes

Keypads and Wall Controls

Receivers

Repair Parts

Challenger Repair Parts

Tec Key TK1010 Remote

Marantec

Remotes

Repair Parts

LiftMaster

Remotes

Keyless Entry

Repair Parts

Receivers

Logic Boards

Surge Protection

Safety Sensors

Wall Controls

Motor Heads

Garage Door Opener Systems

Battery Backup

Accessories

Multi-Code

Remotes

Keypads

Receivers

Universal

Linear Delta3

Remotes

Keypads

Receivers

Repair Parts

Moore O Matic Parts

Heddolf, ESP Micom

Wayne Dalton

Remote Controls and KeyPads

Wall Controls

Repair Parts

Lubricants

Driveway Alert by Optex

Garage Accessories
Customer Assistance
Shipping and Returns
Warranty Information
Cancellation Policy
About Us
Fax or check Order form
Site Index

All orders are shipped same or next day!!!

VISA, Mastercard, American Express and Discover

Review www.garage-door-openers.us on alexa.com

Stanley Garage Door Opener and Gate Operator Keyless Entry System 49442 Programming Instructions

STANLEY KEYPAD CODING INSTRUCTIONS

FEATURES
READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING


The CodeKey Entry System is a wall-mounted, battery-operated keypad that allows anyone to operate the garage door opener as long as that person enters a specific 4-digit ACCESS CODE which is programmed by the owner.

The keypad is back lit with LEDs which are normally off. Pressing ANY key lights the keypad. Each keystroke causes a separate indicator to blink.

The correct "ACCESS CODE" must be entered within 20 keystrokes, otherwise the unit will stop operation for 5 minutes. The user has 25 seconds between keystrokes to enter the correct code, otherwise you must start over.

After the CodeKey has activated by entering the correct (in sequence) "ACCESS CODE", the Stanley Safe-T-Close mode allows ANY key on the CodeKey to be used to open, stop or close the door, for a period of about thirty seconds.

A LOW BATTERY condition is indicated when the keypad lights on the CodeKey go off after the first keystroke entry instead of remaining on.

Important: The installer MUST program the RADIO CODE and ACCESS CODE before the CodeKey will operate the door opener

If you are mounting your keyless entry system to aluminum siding you may find it better to substitute carriage bolts for the mounting screws provided. Bolts should be long enough to reach into the garage and be secured with lockwashers and nuts. If you are mounting your keyless entry system onto brick, stone or mortar, suitable anchors must be set into the mortar, and the fasteners screwed into these.

IDENTIFYING YOUR "RADIO CODE" TYPE

Before setting any codes you need to identify the type of receiver that is in your door opener. You do this by looking at the rear of the power unit hanging in your garage. If your opener has a "LEARN" (remote) button on the back, you have a SecureCode type opener. If your opener has a series of toggle switches or jumper wires, you have a Digital type opener. Identify the type of opener you have at this time.

If you have a SecureCode type opener, go immediately to the Setting the "Access Code" section. If you have a Digital type of opener, you first will have to write down the code setting of the opener. Each toggle switch that is turned ON (closed) or jumper wire that is NOT cut determines the "Radio Code" your CodeKey keypad must be programmed to send.

*If you have toggle switches, write down the numbers that appear below the switches that are turned ON (closed). Example: If Switches numbered 1,2,4,6,9,0 are ON (closed), 1-2-4-6-9-0 will be your "Radio Code". * If you have jumper wires, write down the number of the unclipped wires (ON). Example: If wires 4,8,10 are unclipped, 4-8-0 ill be your "Radio Code".

Note: A "Radio Code" with ALL positions open (OFF) or ALL jumper wires clipped can NOT be used.

SETTING THE "ACCESS CODE"

The ACCESS CODE is a 4-digit code picked by you (sort of a PIN number) which is used to activate the CodeKey unit. The FACTORY SET access code is 1-2-3-4. To change the access code follow these steps:

A. Press the ACCESS LEARN key two (2) times. The red indicating light will blink each time the key is pressed, then it will stay on.

B. If this is the first time the CodeKey is being programmed, enter the FACTORY SET code of 1-2-3-4. If not, enter the access code that was previously programmed.

C. Enter the NEW access code you selected.

D. Press ACCESS LEARN one more time. This eliminates the old access code and installs your new code. If the LED flashes quickly for a few seconds, you will have to re-enter the data because it was not entered correctly.

SETTING THE "RADIO CODE"

At the keypad enter the code as follows:

A. Press the RADIO LEARN key two (2) times. The red indicating light will blink each time the key is pressed then it will stay on.

B. Enter the "Radio Code" that you determined is set on your power unit.

C. Press RADIO LEARN one more time. The red LED should turn off. If the LED flashes quickly for a few seconds, you will have to re-enter the data because it was not entered correctly.

TO OPERATE YOUR GARAGE DOOR

CAUTION: Door opener will activate during the following steps. Keep pathway of garage door clear.

Plug in your door opener at this time. If you have a DIGITAL type opener, entering the four digit ACCESS CODE you selected will activate your door. If you have a SECURECODE type opener, you must first follow these steps to teach the opener the radio code the CodeKey system is sending.

A. Press and release the LEARN button located on the rear of the power unit. The red LED indicator above the LEARN button and on the power unit will come ON, indicating the power unit is now in the LEARN mode.

B. Immediately enter the 4-digit ACCESS CODE you selected in the CodeKey keypad. The CodeKey will send a radio signal to the power unit, then the lights on the power unit will blink two (2) times and turn OFF.

C. Press ANY key on the CodeKey keypad. This will activate the power unit. The power unit "learned" this new radio code.

TROUBLESHOOTING

If at any time you get confused or forget the existing ACCESS CODE, you can RESET the CodeKey to the factory settings. You do this by both pressing the ACCESS LEARN and RADIO LEARN buttons together for ten (10) seconds. This will automatically set the ACCESS CODE to 1-2-3-4, and the RADIO CODE to 0-0-0-0 (this is the SecureCode type setting).

BATTERY REPLACEMENT

The CodeKey will always "remember" the last codes you programmed even if the battery is removed. A 9-volt battery is used.

garage-door-openers.us - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981.  Providing excellent customer service and assistance for over 25 years. We are a discount reseller of  garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community.   We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. All mentioned brand names of Garage Door openers, Garage Door opener receivers and Gate operator devices are registered trade names and trademarks of the respective entities and are only used for reference.

1st Garage Door Openers Inc.

Mesa, AZ  85203

1-480-247-2094

1-480-247-3498   Fax

Garage Door and Garage Door Openers

Copyright 2017 garage-door-openers.us  No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.