Garage Door Openers, Garage Door Opener Parts, Access Controls, Garage Door Opener Remote Control and Garage Door Keypad

garage-door-openers.us your garage door opener specialists Sales 1-480-247-2094

 

 Home

Contact Us

About Us

Shipping

Follow us on Facebook

1st Garage Door Openers, Inc.
 BBB Business Review

Stanley

Remotes

Receivers

Keyless Entry and Wall Controls

Repair Parts

Telectron

Allister,Allstar

Remotes

Keypads and Wall Controls

Receivers

Repair Parts

Challenger Repair Parts

Tec Key TK1010 Remote

Marantec

Remotes

Repair Parts

LiftMaster

Remotes

Keyless Entry

Repair Parts

Receivers

Logic Boards

Surge Protection

Safety Sensors

Wall Controls

Motor Heads

Garage Door Opener Systems

Battery Backup

Accessories

Multi-Code

Remotes

Keypads

Receivers

Universal

Linear Delta3

Remotes

Keypads

Receivers

Repair Parts

Moore O Matic Parts

Heddolf, ESP Micom

Wayne Dalton

Remote Controls and KeyPads

Wall Controls

Repair Parts

Lubricants

Driveway Alert by Optex

Garage Accessories
Customer Assistance
Shipping and Returns
Warranty Information
Cancellation Policy
About Us
Fax or check Order form
Site Index

All orders are shipped same or next day!!!

VISA, Mastercard, American Express and Discover

Review www.garage-door-openers.us on alexa.com

Wayne Dalton Garage Door Openers Keyless Keypad Entry System

#1 Programming or Changing Personal Identification Number (PIN)

To start the programming, push the PIN/RESET button. Two green LED lights will go on which indicates the unit has been activated and waiting for commands. These same green LED’s help illuminate the keypad in the dark for easy reading. The Wireless Keypad has an energy saving feature that will reset the unit to “standby” after 20 seconds, the green LED’s will go out and the unit will shut down. If this happens while you are programming, simply start over again.

Press the Star (*) key. All key presses are confirmed by the yellow LED blinking once.

Enter the factory set, 4-digit system code 9999.

Press the Star (*) key. The yellow LED will flash three times to acknowledge that it is now in the programming mode.

Enter the 4-digit personal identification number (PIN) you wish to use.

Enter the number of door openers that your Model 297138 Wireless Keypad will be operating. (Between 1 and 4).

                                          1= Single door                         3= 3 doors

                                          2= 2 doors                              4= 4 doors

Press the Pound (#) key. The yellow LED should stay on for two seconds, then the Green LED will blink, and finally, the Yellow LED will flash 2 times indicating the new user code has been properly programmed into your Wireless Keypad.

NOTE: IF AT NAY TIME, AN ERROR WAS MADE IN ENTERING THE CODES, SIMPLY PRESS THE ON/RESET BUTTON AND REPEAT THE ABOVE PROCEDURES.

#2 programming the Model 297138 Wireless Keypad to work with the openers

built in receiver.

Activate the opener learning mode by pressing the PROGRAM SWITCH (SW) button located on the Motor Head Unit, once (if the wired deluxe Wall Station is installed, refer to your manual for activation using the alternative programming switch). The PROGRAM STATUES L.E.D. on the motor head unit will light and remain lit, indicating that the receiver is ready to receive the radio transmitter code signal and learn its own security code.

 

Press the ON/RESET button to activate the keypad and enter * 9999* (your personal 4-digit PIN) (number of doors) #. This will put the wireless keypad into the “teach mode.” Now press the ON/RESET button and enter your personal 4-digit PIN number is all that is needed to activate the door. (If your wireless keypad is being used for multiple doors, enter the number of the door you are activating {e.g. 1234 1}.

Repeat step #2 for each door.

The PROGRAM STATUS L.E.D. on the motor head unit should turn itself off, indicating it has learned the transmitter signal and will start its “roaming” security code system sequence.

NOTE: For multiple door installations, use your 4-digit Personal Identification Number (PIN) PLUS the door number you’re activating, each time you use your wireless keypad. Make sure the Program Status LED is illuminated only on the opener to be programmed.

NOTE: If the Motor Head Unit is not learning the Wireless Keypad properly, repeat step #2.

How your Wireless Keypad Operates your Opener

The following explains how your Wireless Keypad can be used to OPEN, CLOSE, START and STOP your door.

To issued a door command:

1.      Activate your keypad by pressing the ON/RESET button.

2.      Enter your 4-digit personal identification number (PIN), PLUS the door number, if your keypad is set up for more than one door. (If your keypad is programmed for a single door, then the 4-digit PIN number is all that is needed to activate door). The green Led will blink twice and a radio signal will be sent to the opener.

NOTE: If you inadvertently enter as incorrect code, the yellow light will blink for 2 seconds and shut down the keypad. Reactivate with the ON/RESET button and reenter your personal identification number (PIN).

3.      For a period of 20 seconds from your last keypress, you can control the motion of your door with the Wireless Keypad by pushing any button EXCEPT THE ON/RESET Button. Each pressing of a key sends a signal to the opener and will start/stop/reverse according to the operation of the opener. Refer to your openers operating manual for a full understanding of how the door travel will react to each signal in the OPEN and CLOSE cycles.

LOW BATTERY WARNING

The low battery warning system will alert you when the battery need to be replaced with a blinking yellow light when you first activate the keypad with the ON/RESET button. This light will continue to blink until another key is activated or the 20-second time-out shuts off the unit. We recommend replacing the Alkaline batteries. Under normal operating conditions a battery should last 12 months. Dispose of batteries properly.

 

 

 

    

garage-door-openers.us - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981.  Providing excellent customer service and assistance for over 25 years. We are a discount reseller of  garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community.   We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. All mentioned brand names of Garage Door openers, Garage Door opener receivers and Gate operator devices are registered trade names and trademarks of the respective entities and are only used for reference.

1st Garage Door Openers Inc.

Mesa, AZ  85203

1-480-247-2094

1-480-247-3498   Fax

Garage Door and Garage Door Openers

Copyright © 2017 garage-door-openers.us  No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.